View AT-09632JFIEB-52H_4414100.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AMP I RE
SPECIFICATIONS FOR LCD MODULE
CUSTOMER CUSTOMER PART NO. AMPIRE PART NO. APPROVED BY DATE
Approved For Specifications
Approved For Specifications & Sample
AT-09632JFIEB-52H(R)
APPROVED BY
CHECKED BY
ORGANIZED BY
Date : 2005/7/1
AMPIRE CO., LTD.
1
RECORD OF REVISION
Revision Date 2005/7/1 2006/9/7 Page 3 Contents New Release Modify Mechanical data Editor Tony Tony
Date : 2005/7/1
AMPIRE CO., LTD.
2
1
(1) (2) (3) (4) (5) (6) (7) (8)
FEATURES
Display format : 96 x 32 dot-matrix, 1/33 duty, 1/6 Bias. Construction : LCD panel, Blue EL backlight and TAB IC Display type : FSTN, Transflective, Positive, 6 o'clock view LCD Controller :NT7534 Interface for 8-bits 80 series MPU. Extended temperature type. IC Segment 0~95. ROHS compliable.
2
MECHANICAL DATA
Parameter Dot size Dot pitch Viewing area Module size Stand Value 0.235(W) x 0.235(H) 0.25(W) x 0.25(H) 30.0(W) x 9.5(H) 39.5(W) x 33.9(H) x 2.2 max (T) Unit mm mm mm mm
3
ABSOLUTE MAXIMUM RATINGS
Parameter Logic Circuit Supply Voltage LCD Driving Voltage Input Voltage Operating Temp. Symbol VDD VLCD VI TOP TSTG Min 2.7 -VSS 0 -20 Max 3.5 6.0 VDD 50 70 Unit V V V C C
Extended temp. type Storage Temp.
Date : 2005/7/1
AMPIRE CO., LTD.
3
4
ELECTRO-OPTICAL CHARACTERISTICS
Parameter Symbol Condition Min Typ Max Unit Note
----- Electronic Characteristics ----Logic Circuit Supply Voltage LCD Driving Voltage VDD-VSS V0-VSS --20 C 25 C 70 C Input Voltage VIH VIL Logic Supply Current IDD --VDD = 3.0V 2.7 ---2.2 VSS ---6.0 ----3.5 ---VDD 0.6 0.3 V V mA V V
----- Optical Characteristics ----Contrast Rise Time Fall Time Viewing Angle Range CR tr tf f b l r Frame Frequency fF 25C FSTN type 25C 25C 25C & CR2 --------7 200 200 40 35 40 40 33 --------Hz Deg. ms ms Note 3 Note 1 Note 2
(NOTE 1) Contrast ratio : CR = (Brightness in OFF state) / (Brightness in ON state)
Date : 2005/7/1
AMPIRE CO., LTD.
4
( NOTE 2 ) Response time :
(NOTE 3) Viewing angle
Date : 2005/7/1
AMPIRE CO., LTD.
5
EL Back-light Electrical Specification
Parameter Color Voltage Frequency Current Density Bare EL Initial Brightness LCM Initial Brightness Specification Blue Vrms = 110 Sine Wave = 400 0.12 40 6 Unit V(AC) Hz mA / cm2 cd / m2 cd / m2
Date : 2005/7/1
AMPIRE CO., LTD.
6
D
B
C
5
A
B
C
A D
1
1
1
1
U? NT7502-1
09632J LCM
2
2
P3.0
VDD
NC NC NC
3
3
C1 a
COM63
Date : 2005/7/1
C16
P3.1 P3.3 P3.4 P3.5 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7
COM48
266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298
VSS
NC1 a
NT7502
BLOCK DIAGRAM
4
4
COM32 COM33 COM34 COM35 COM36 COM37 COM38 COM39 COM40 COM41 COM42 COM43 COM44 COM45 COM46 COM47 COM48 COM49 COM50 COM51 COM52 COM53 COM54 COM55 COM56 COM57 COM58 COM59 COM60 COM61 COM62 COM63 COMS
2
C1 1uF C2 1uF C3
5
2
NC16 NC1 a
5
1uF
NC36 S1
SEG95
C4 1uF C6 1uF C8 1uF
6
C5 1uF C7 1uF
6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 NC NC NC NC FR CL /DOF NC /CS1 CS2 /RES A0 /WR(R//W) /RD(E) D0 D1 D2 D3 D4 D5 D6 D7 DUTY0 DUTY1 VDD VDD2 VSS VOUT NC CAP3+ CAP1CAP1+ CAP2+ CAP2VEXT VRS V1 V2 V3 V4 V0 VR M/S CLS C86 P/S /HPM IRS NC 3
3
NT7502
7 8
7
8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
NC FRS FR CL /DOF NC VSS /CS1 CS2 VDD /RES A0 VSS /WR /RD VDD D0 D1 D2 D3 D4 D5 D6 D7 VSS VDD DUTY0 DUTY1 VSS VDD VDD VDD VDD VDD2 VDD2 VDD2 VSS VSS VSS VSS VOUT VOUT CAP3+ CAP3+ CAP1CAP1CAP1+ CAP1+ CAP2+ CAP2+ CAP2CAP2VDD VEXT VRS VSS V1 V1 V2 V2 V3 V3 V4 V4 V0 V0 VR VR VSS VSS VDD M/S CLS VSS C86 P/S VDD /HPM VSS IRS VDD TMPS VSS TEST0 NC TEST1 NC TEST2 VSS TEST3 VDD NC NC NC NC NC NC NC NC NC
SEG0
9
9
SEG131 SEG130 SEG129 SEG128 SEG127 SEG126 SEG125 SEG124 SEG123 SEG122 SEG121 SEG120 SEG119 SEG118 SEG117 SEG116 SEG115 SEG114 SEG113 SEG112 SEG111 SEG110 SEG109 SEG108 SEG107 SEG106 SEG105 SEG104 SEG103 SEG102 SEG101 SEG100 SEG99 SEG98 SEG97 SEG96 SEG95 SEG94 SEG93 SEG92 SEG91 SEG90 SEG89 SEG88 SEG87 SEG86 SEG85 SEG84 SEG83 SEG82 SEG81 SEG80 SEG79 SEG78 SEG77 SEG76 SEG75 SEG74 SEG73 SEG72 SEG71 SEG70 SEG69 SEG68 SEG67 SEG66 SEG65 SEG64 SEG63 SEG62 SEG61 SEG60 SEG59 SEG58 SEG57 SEG56 SEG55 SEG54 SEG53 SEG52 SEG51 SEG50 SEG49 SEG48 SEG47 SEG46 SEG45 SEG44 SEG43 SEG42 SEG41 SEG40 SEG39 SEG38 SEG37 SEG36 SEG35 SEG34 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0
265 264 263 262 261 260 259 258 257 256 255 254 253 252 251 250 249 248 247 246 245 244 243 242 241 240 239 238 237 236 235 234 233 232 231 230 229 228 227 226 225 224 223 222 221 220 219 218 217 216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134
COMS COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM8 COM9 COM10 COM11 COM12 COM13 COM14 COM15 COM16 COM17 COM18 COM19 COM20 COM21 COM22 COM23 COM24 COM25 COM26 COM27 COM28 COM29 COM30 COM31
4
4
S96 NC
133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101
COM0 C32 a
COM15
10
10
AMPIRE CO., LTD.
C17 NC1 a
CHK. DWN.
File:
APPD.
NC16
11
11
Size 12
Title
A1
Date: File: C D
Number
5
5
3-Jun-2003 C:\WINDOWS\Desktop\AT-09632J.sch
Sheet of Drawn By:
12
Revision
B
Size:
B
Date:
A
Number:
Sheet 6 Rev. of
6
AMP I R E
7
C
B
A
D
6
INTERFACE
No. 1~4 5 6 7 8 9 10 11 12 13 14 Symbol NC FR CL DOF NC CS1 CS2 RES A0 WR RD D0~D7 DUTY0 DUTY1 VDD VDD2 VSS VOUT NC CAP3+ CAP1CAP1+ CAP2+ CAP2VEXT VRS V1 V2 V3 V4 V0 VR M/S CLS Voltage adjustment pad. Select the Master/Slave operation. "H" internal oscillator circuit is enabled. "L" internal oscillator circuit is disabled. No connection M/S="H" Output; M/S="L" Input. This is the display clock input terminal. M/S="H" Output; M/S="L" Input. No connection Chip select Chip select Set="L" Settings are initialized. "H" D0-D7 are display data; "L" D0-D7 are control data. 8080 MPU It's active"L"; 6800 MPU "H"Read, "L"Write. 8080 MPU It's active"L"; 6800 MPU It's active"H". 8-bit data bus for 80 series MPU Select the LCD driver duty. Select the LCD driver duty. Power supply 2.4-3.5V This is the reference power supply. Ground DC/DC Voltage Converter. No connection Capacitor3+ pad for internal DC/DC Voltage Converter. Capacitor1- pad for internal DC/DC Voltage Converter. Capacitor1+ pad for internal DC/DC Voltage Converter. Capacitor2+ pad for internal DC/DC Voltage Converter. Capacitor2- pad for internal DC/DC Voltage Converter. Vext must be > 2.4V and < Vdd2. "0" using the external Vref; "1" using the internal Vref. LCD driver supply voltage: Voltages should have the following relationship; V0 > V1 > V2 > V3 > V4 > Vss Function
15~22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44
Date : 2005/7/1
AMPIRE CO., LTD.
8
45 46 47 48 49
C86 P/S HPM IRS NC
"H" 6800 Series MPU interface; "L" 8080 MPU interface. This is parallel data. "H" Normal mode; "L" Hight power mode. "H" use the internal resistors "L" Don't use the internal resistors No connection
Date : 2005/7/1
AMPIRE CO., LTD.
9
7
INSTRUCTION SET
Date : 2005/7/1
AMPIRE CO., LTD.
10
8
TIMING CHARACTERISTICS
Date : 2005/7/1
AMPIRE CO., LTD.
11
Date : 2005/7/1
AMPIRE CO., LTD.
12
9
QUALITY AND RELIABILITY 9.1 TEST CONDITIONS
Tests should be conducted under the following conditions : Ambient temperature : 25 5C Humidity : 60 25% RH.
9.2
SAMPLING PLAN
Sampling method shall be in accordance with MIL-STD-105E , level II, normal single sampling plan .
9.3 ACCEPTABLE QUALITY LEVEL
A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. A minor defect is one that does not materially reduce the usability of the unit for its intended purpose or is an infringement from established standards and has no significant bearing on its effective use or operation.
9.4 APPEARANCE
An appearance test should be conducted by human sight at approximately 30 cm distance from the LCD module under flourescent light. The inspection area of LCD panel shall be within the range of following limits.
Date : 2005/7/1
AMPIRE CO., LTD.
13
9.5
Item
INSPECTION QUALITY CRITERIA
Description of defects Class of Defects Major Major Minor Acceptable level (%) 0.65 1.5 2.5
Function Dimension Black spots
Black lines
Bubbles in polarizer Color uniformity Glass Scratches Contrast ratio Response time Viewing angle
Short circuit or Pattern cut Deviation from drawings Ave . dia . D area A area B Disregard D0.2 3 4 0.2 0.5 for N = 1 Rainbow color or newton ring. Obvious visible damage. See note 1 See note 2 See note 3
Minor
2.5
Minor Minor Minor Minor Minor Minor
2.5 2.5 2.5 2.5 2.5 2.5
ZONE A active area ZONE B viewing area
Date : 2005/7/1
AMPIRE CO., LTD.
14
9.6 RELIABILITY
Test Item High Temperature Operation Low Temperature Operation High Temperature Storage Low Temperature Storage Test Conditions 703C , t=96 hrs -203C , t=96 hrs 803C , t=96 hrs 1,2 Note
1,2 -303C , t=96 hrs -30C ~ 25C ~ 80C Thermal Shock Test 1,2 30 min. 5 min. 30 min. ( 1 cycle ) Total 5 cycle Sweep frequencyG 10~55~10 Hz/1min Amplitude : 0.75mm Vibration Test (Packing) 2 Test direction : X.Y.Z/3 axis Duration : 30min/each axis Note 1 : Condensation of water is not permitted on the module. Note 2 : The module should be inspected after 1 hour storage in normal conditions (15-35C , 45-65%RH). Definitions of life end point : Current drain should be smaller than the specific value. Function of the module should be maintained. Appearance and display quality should not have degraded noticeably. Contrast ratio should be greater than 50% of the initial value.
Date : 2005/7/1
AMPIRE CO., LTD.
15
10 HANDLING PRECAUTIONS
(1) An LCD module is a fragile item and should not be subjected to strong mechanical shocks. (2) Avoid applying pressure to the module surface. This will distort the glass and cause a change in color. (3) Under no circumstances should the position of the bezel tabs or their shape be modified. (4) Do not modify the display PCB in either shape or positioning of components. (5) Do not modify or move location of the zebra or heat seal connectors. (6) The device should only be soldered to during interfacing. Modification to other areas of the board should not be carried out. (7) In the event of LCD breakage and resultant leakage of fluid do not inhale, ingest or make contact with the skin. If contact is made rinse immediately. (8) When cleaning the module use a soft damp cloth with a mild solvent, such as Isopropyl or Ethyl alcohol. The use of water, ketone or aromatic is not permitted. (9) Prior to initial power up input signals should not be applied. (10) Protect the module against static electricity and observe appropriate anti-static precautions.
Date : 2005/7/1
AMPIRE CO., LTD.
16
11 OUTLINE DIMENSION
Date : 2005/7/1
AMPIRE CO., LTD.
o
u
q
i
17

▲Up To Search▲

Price & Availability of AT-09632JFIEB-52H

	To Download AT-09632JFIEB-52H Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .